Ling King
Favorite team: | LSU |
Location: | Gulfport MS |
Biography: | |
Interests: | |
Occupation: | |
Number of Posts: | 173 |
Registered on: | 2/5/2012 |
Online Status: | Not Online |
Recent Posts
Message
re: Looked at 3 straight strikes!!
Posted by Ling King on 4/5/24 at 10:10 pm
Agree! He talks too much. ...
re: Current building cost on the coast?
Posted by Ling King on 11/22/23 at 10:39 am
For just the house? It can be done. Finishes will ultimately determine how much above or below that figure you will be. ...
re: Current building cost on the coast?
Posted by Ling King on 11/21/23 at 1:54 pm
As others have stated, lots of variables. But $300-325 sqft will get you a nice place. I just built one in Bay St Louis as a spec and it brought $325/ sqft. 1500 sqft and was not water front but was raised. ...
re: Any LVP experience?
Posted by Ling King on 6/8/23 at 7:32 pm
That’s caused from him not tapping them in good. You will have to pull back the flooring at least 2 to 3 strips over from where the separating is occurring to tap it in....
re: Drywall labor prices
Posted by Ling King on 5/17/23 at 10:39 pm
Sqft of entire surface area...
re: Drywall labor prices
Posted by Ling King on 5/16/23 at 8:03 pm
Ceiling height, and finished corners like windows and wall/ ceilings play a part but I pay .60-.65 per sqft on average for my houses for a slick finish...
re: 2 sack crawfish boiler?
Posted by Ling King on 1/7/23 at 10:06 am
[quote]I checked out their website though. You would think that with jet burners and no heat shield/wind shield covering the sides of the burners that it would lose a ton of heat and not get water boiling too fast....[/quote]
I can bring my pot with 20 gallons of water to a boil in 7-8 minutes. ...
re: 2 sack crawfish boiler?
Posted by Ling King on 1/5/23 at 10:38 pm
I think I paid $1800 for my first pot with a dump basket. Could do 3 sacks at a time. But it had a pot cooler on it too. I traded it to a buddy and bought one without a dump basket. It has a steaming rack though Give Cary a call; he will build you whatever you want ...
re: 2 sack crawfish boiler?
Posted by Ling King on 1/4/23 at 10:17 pm
I have purchased 2 from Gator Pots out of Slidell. IMO, you will not find a better made pot with the versatility. ...
re: Can y’all tell me about Smoke Laval?
Posted by Ling King on 6/1/22 at 10:36 pm
This is very true. Smoke had too much ego and not enough motivation for players. Overall he was a piece of shite too...
re: Homeowners insurance claim question
Posted by Ling King on 5/17/22 at 9:08 pm
I’m in the industry and will tell you if they ordered an engineers report they are setting up to deny the claim because they feel there are grounds to do so. I would request the engineers report and go over it with a licensed/qualified roofer you trust. If they feel the damage was sudden and non for...
re: Making sure sod "takes"
Posted by Ling King on 5/2/22 at 9:40 pm
Y’all be careful pulling that drag with your mower. I fried both my hydro pumps on my Scag Turf Tiger like that ??. ...
re: Standing Seam on Existing Shingle Roof
Posted by Ling King on 12/30/21 at 10:57 pm
Don’t do it! As others have said, you need to inspect the substrate. Also, going over the shingles could cause oil canning. This is a waviness in the panel. ...
re: Going rate per square shingles installed Jefferson Parish
Posted by Ling King on 11/26/21 at 9:23 pm
Lots of variables but Art is dead on....
re: New Metal Roof Recs in BSL...
Posted by Ling King on 11/24/21 at 5:44 pm
[quote] I'm debating standing seam vs R-Panel but the price is double. Is it worth it?[/quote]
In my opinion you are also paying for the appearance of the standing seam.. The standing seam is a nice system because it hides the screws however the new 40 year screws have come along way. ...
re: New Metal Roof Recs in BSL...
Posted by Ling King on 11/23/21 at 10:03 pm
Was not sure if you had the amount of roofing squares; was going to give you price ranges. For a galvalume R panel roof with Zac screws, ice and water, and 2x4 stripping you should be expecting $600-700 per square. For standing seam, it will be more in the $1000-1200 per square range. A lot of what ...
re: New Metal Roof Recs in BSL...
Posted by Ling King on 11/22/21 at 9:52 pm
How many squares? Galvalume?...
re: Tamko Titan Roof Shingles
Posted by Ling King on 11/16/21 at 9:40 am
Ok, I’ll be more specific. The Tamko Heritage shingles that are readily available and being sold to property owners are Builders Grade shingles. I have put the on and taken them off of roof tops. They are very thin and tear easily. I can’t speak to their Titan or class 4 shingles as I typically inst...
re: Tamko Titan Roof Shingles
Posted by Ling King on 11/16/21 at 9:11 am
Depends on color, but for most of them the longest wait is 2 weeks. Hearthstone is the color taking the longest for us. A lot of these are going to Laplace, Gonzales, Lutcher areas. ...
re: Tamko Titan Roof Shingles
Posted by Ling King on 11/15/21 at 7:38 pm
Tamko is a builders grade shingle. I have not installed any Titans but I highly doubt they are of the quality of Atlas or OC Duration. I would call around and get other quotes. I get Atlas Pinnacle Pristine weekly. Popular colors are 2 weeks at most. ...
Popular